High Voltage 50 Ω Pulse Generator
Features
- High voltage transmission line pulse (TLP) generator
- Rectangular pulse shape
- 50 Ω high voltage TNC pulse output connector
- ±4 kV output voltage (50 Ω output load)
- ±160 A output current (output short circuit)
- 320 kW peak pulse output power into 50 Ω load
- 0.6 ns to 50 ns digital programmable pulse rise time in 6 custom selectable steps
- 100 ns pulse width
- Optional Human Metal Model (HMM) pulse shape, equivalent to ±43 kV according IEC 61000-4-2 (330 Ω, 150 pF)
- Optional external manual pulse width extender TLP-16012A for 10 ns to 500ns pulse width
- 5 Hz pulse repetition frequency
- High speed 50 Ω, 1 V trigger output for digital oscilloscopes (synchronous to high voltage pulse output)
- Software driver for stand-alone operation
- Efficient software for system control, waveform analysis and waveform data management (optional)
- Integrated interlock safety shut-down
- Industrial isolated and EMI/ESD protected USB control interface
Download: Product Datasheet TLP-16010A
Download: Laboratory Safety Notes
TLP-16010A Front View
TLP-16010A Rear View
Accessories suitcase included with TLP-16010A (typical set)
The table below lists accessories equipped with SMA and TNC connectors.
SMA connectors can withstand pulse voltages of 2–3 kV, provided that the dielectric interface is clean and the connector is properly tightened to a torque of 1 Nm.
This voltage range is sufficient for most devices under test (DUTs) with breakdown voltages below 1 kV. In such cases, SMA accessories are suitable and offer better RF performance for VF-TLP measurements than TNC accessories.
For high-voltage testing at DUT voltages of 2 kV and above, TNC accessories are recommended.
Typical SMA accessories for TLP-16010A
| Item | ||||
| Item | Sub-Item | Qty. | Description | Model Number |
| 1 | 1.0 | 1 | TLP/VF-TLP/HMM base unit TLP-16010C | TLP-16010C |
| 1.1 | 1 | High current HMM waveform module HMM-16010A | HMM-16010A | |
| 1.2 | 1 | 3 kV, 9 GHz DUT Switch For TLP-12010A/C Pulser | S-3000DK | |
| 1.3 | 1 | DUT switch control cable 2 m | PCC-200A | |
| 1.4 | 1 | DUT switch control cable 1 m | PCC-100A | |
| 1.5 | 1 | Resistive termination network 500 Ω setup | HIT-526A | |
| 1.6 | 1 | 50 Ω SMA current sensor module 160 A, 3 GHz, 0.5 V/A | ||
| 1.7 | 1 | PCB adaptor | PBA-3002A | |
| 1.8 | 1 | TLP calibration kit for PCB measurements | CAL-KIT-200-A3 | |
| 1.9 | 1 | TLP calibration kit for wafer level measurements | CAL-03A | |
| 1.10 | 1 | SMA wideband pickoff-tee | PT-45A | |
| 1.11 | 1 | 30 kHz – 7 GHz, 10 A DC high current bias tee for TLP/VF-TLP/HMM and charge recovery measurements | ||
| 1.12 | 4 | BNC(m) to SMA(fm) adaptor | BNC(m)/SMA(fm) | |
| 1.13 | 2 | SMA(m)/SMA(m) adaptor | SMA(m)/SMA(m) | |
| 1.14 | 2 | SMA(f)/SMA(f) adaptor | SMA(f)/SMA(f) | |
| 1.15 | 1 | TNC(m) to SMA(m) adaptor | TNC(m)/SMA(m) | |
| 1.16 | 1 | 10 dB, 18 GHz SMA attenuator | 18AH-10 | |
| 1.17 | 1 | 20 dB, 18 GHz SMA attenuator | 18AH-20 | |
| 1.18 | 1 | 2 x 4 mm (m) to BNC(f) adaptor, (Keithley 2400 front-side adaptor) | 2x4mm (m)/BNC(f) | |
| 1.19 | 3 | Flexible RG188A/U SMA(m)/SMA(m) 50 Ohm cable, 2 m, for current sensor and DUT leakage | RG188-2m | |
| 1.20 | 2 | 50 Ohm SMA cable 1 m, Sucoflex 104, for PCB adaptor | SF104−1m | |
| 1.21 | 4 | 50 Ohm SMA cable 2m, Sucoflex 104, for pulse sense/force and vf-TLP delay line | SF104-2m | |
| 1.22 | 1 | Transient voltage suppressor protection for scope input | TVS-70MF-10 | |
| 1.23 | 1 | Power line cable according supply voltage, 150 cm | PLC-150A | |
| 1.24 | 1 | SMA torque wrench | 74Z-0-0-21 | |
| 1.25 | 1 | TLP software (object code) | TLP-GUI-OC | |
| 1.26 | 1 | TLP software manual | TLP-SM | |
| 1.27 | 1 | Hardware manual TLP-16010A | TLP-HM | |
| 1.28 | 1 | Interlock Safety Shut Down (incl.) | TLP-IN-LO | |
| 1.29 | 1 | USB 2.0 Cable A Male to B Male 9.84″ (3.00m) Shielded | 102-1030-BL-F0300 |
Optional TNC accessories for TLP-16010A
| Item | ||||
| Item | Sub-Item | Qty. | Description | Model Number |
| 2 | 2.0 | 1 | 4 kV, 5 GHz DUT Switch For TLP-16010A/C Pulser | S-3000DK-TNC |
| 2.1 | 1 | 50 Ω, 160 A, 2 GHz, 0.5 V/A Current Sensor | CS-0V5-A-TNC | |
| 2.2 | 1 | PCB Adaptor | PBA-3002-TNC | |
| 2.3 | 1 | 4 kV, 50 Ω SMA Wideband Pick-Off Tee | PT-45B-TNC | |
| 2.4 | 1 | 100 V, 2 A, 30 kHz – 7 GHz High Voltage Bias Tee | BT-10100-TNC | |
| 2.5 | 1 | High Voltage Attenuator 10 dB, 50 Ω | HVA-10A-TNC | |
| 2.6 | 1 | High Voltage Attenuator 20 dB, 50 Ω | HVA-20A-TNC | |
| 2.7 | 4 | TNC(m) to SMA(m) adaptor | TNC(m)/SMA(m) | |
| 2.8 | 4 | TNC(m)/TNC(m) adaptor | TNC(m)/TNC(m) | |
| 2.9 | 4 | TNC(f)/TNC(f) adaptor | TNC(f)/TNC(f) | |
| 2.10 | 2 | TNC(m)/TNC(f) adaptor | TNC(m)/TNC(f) | |
| 2.11 | 4 | 50 Ohm HV-HF cable 2m | RG142-2m-TNC(m)/TNC(m) | |
| 2.12 | 2 | 50 Ohm HV-HF cable 1m | RG142-1m-TNC(m)/TNC(m) |



